[2026] Valid Civil-Engineering-Technology test answers & CTTAM Civil-Engineering-Technology exam pdf [Q37-Q54]

Posted On October 2, 2026

[2026] Valid Civil-Engineering-Technology test answers & CTTAM Civil-Engineering-Technology exam pdf

Verified Civil-Engineering-Technology dumps Q&As – Pass Guarantee or Full Refund

NO.37 A civil engineering technologist asked an engineer in training (EIT) to write a deficiency report. After a few revisions, the report is still disorganized and has errors. What would be an appropriate action to take for the technologist?

Report the EIT to the supervisor and recommend training.

Explain to the EIT the importance of meeting deadlines.

Assist the EIT in re-writing the report.

Complete the document on behalf of the EIT.

NO.38 What is a silt fence used for?

To mark the construction limits of the project

To prevent water from moving through the site

To prevent the public from accessing the construction site

To prevent soil from moving through the site due to erosion

NO.39 A civil engineering technologist is undertaking a final acceptance review of a subdivision. The technologist finds 35 m of deficient sidewalk and three hydrants which were not tested. As part of final acceptance, what should be done to ensure the hydrants get tested and the sidewalk is repaired?

Write down that three hydrants were not tested, and that 35 m of sidewalk was deficient.

Verbally communicate the locations of the hydrants and the sidewalk to the contractor.

Write down the locations of the hydrants and the sidewalk and forward the deficiency list to the contractor.

Request that the contractor write down the numbers and locations of the hydrants and the sidewalk.

NO.40 Which of the following images shows the appropriate tool to measure the slump of concrete?

Option A

Option B

Option C

Option D

NO.41 Which structural components are indicated by the letters A, B, C, and D in the image below?

Pier / Ledger / Joist / Decking

Post / Girder / Stringer / Sheathing

Post / Joist / Beam / Decking

Column / Joist / Girder / Sheathing

NO.42 A site inspection reveals a beam that does not conform to Issued for Construction (IFC) drawings. What should be done?

Document the issue and notify the engineer

Remove the beam and notify the contractor

Document the issue and file it

Verify engineering calculations on IFC drawings

NO.43 What subsurface sampling would be most likely conducted during a preliminary site investigation for a proposed building?

Soil samples and borehole logs

Atterberg limits and detailed grading plans

Proctor densities and final building elevations

Marshall tests and proposed driveway locations

NO.44 What is a typical concrete slump for a municipal sidewalk?

10-50 mm

25-75 mm

50-100 mm

80-100 mm

NO.45 A soil sample has a porosity of 40%, and the specific gravity of solids is 2.60. What would be the approximate value of dry density of the soil if the soil is completely saturated?

15.30 kN/m³

20.45 kN/m³

25.85 kN/m³

40.25 kN/m³

NO.46 A continuous beam is supported in the middle and at both ends. It has a uniform load applied to the top. What will be the reactive forces at the supports?

They will be equal at all supports.

They will be greater in the middle than at the ends.

They will be greater at the ends than in the middle.

They will vary depending on whether the supports are fixed or not.

NO.47 A civil engineering technologist works for a contractor. An engineer notifies him that the depth of concrete pilings needs to be increased. What is the first thing the civil engineering technologist should do?

Proceed with the work according to the original contract.

Proceed with the revised work as instructed.

Present revised environmental considerations to the project engineer.

Present the change in costs and schedules to the project manager.

NO.48 Which of the following tests would most likely be used to determine if engineered fill was placed to meet contract specifications?

Sieve analysis

Compaction test

Triaxial compression test

Moisture content check

NO.49 What material property is measured by a sieve analysis?

Angularity

Mass

Moisture density

Gradation

NO.50 EXCERPT FROM MUNICIPAL BYLAW 1234 – ZONING
Section 3: Single family zone
3.1 All dwellings shall house one family.
3.2 All dwellings shall have a minimum main floor area of 120 m².
3.3 All dwellings shall be constructed a minimum of 10.0 m from the front property line, 15.0 m from the rear property line, and 1.5 m from the side property lines.
3.4 An application that does not fulfill the above requirements shall be referred to Council.

Approve the application because it meets all requirements.

Reject the application because the rear yard setback is too large.

Refer the application to Council because it does not meet the requirements.

Reject the application because one of the side yard dimensions and the main floor area are not sufficient.

NO.51 Which of the following is the best location for a foundation perimeter drain pipe?

At the footing elevation, outside the foundation

At the footing elevation, inside the building

Above the footing elevation, outside the building

Below the frost line, outside the footing

NO.52 When should soil compaction tests be completed?

During pre-design

During backfill of a trench