[Jun 04, 2023] Get Latest and 100% Accurate NACE-CIP1-001 Exam Questions [Q39-Q54] : Best Free Exam Guide : http://free.exams4sures.com

NO.39 The Inspector should record the serial numbers of inspection instruments:

Only if the specification requires it

Each time the instrument is used

Only if the instrument is suspected of not working properly

Only when verifying accuracy of the instrument

NO.40 Checking is

an exposed area of the substrate or previous coat material, caused by poor application technique.

a fine crack in the surface of a coating that rarely reaches the substrate

a very small hole in a coating caused when air or solvent is trapped in porous film and then escapes.

surface breaks in the film that often result from grease or oil contamination and revel the substrate.

NO.41 A NACE Coating Inspector is permitted to transport coating material when:

Asked to do so by the Coating Application team

Asked to do so by the Owner’s Representative

The Inspector should never transport coating material

If the Inspector meets all the necessary requirements for Transportation of Dangerous Goods

NO.42 Good records can provide maintenance departments with detailed information about ALL of the following EXCEPT

what items were coated.

what materials were used.

when the coating will be reapplied.

how the item was coated.

NO.43 Surface profile describes:

The level of surface cleanliness required after abrasive blasting

The level of surface roughness required after abrasive blasting

The initial condition of the surface prior to abrasive blasting

The general condition of the surface required after abrasive blasting

NO.44 The initial steel condition is important to the NACE Inspector because:

If the steel is pitted more coating will be required

Less abrasive is need if the mill Scale s gone

It affects the final appearance after blasting

The Inspector may have to reject the Steel

NO.45 What is the minimum spot measurement value allowed by SSPC-PA 2 in each 10 m2 (100 ft2) area?

70% of the specified maximum thickness

80% of the specified minimum thickness

90% of the specified maximum thickness

100% of the specified maximum thickness

NO.46 Prior to the pre-job conference you notice that the Inspection and Test Plan does not require a hold point after surface preparation and coating application. In speaking with the owners’ representative in advance of the meeting you sense he/she does not understand the importance of the hold point.
As a NACE CIP Level 1 Inspector your preferred course of action is to:

Gather data and attempt to meet with the owner’s representative in advance of the pre-job conference

Bring the matter up at the pre-job conference

Default to the owner’s Inspection and Test Plan

Meet separately with the coating manufactures’ representative and coating application company in advance of the pre-job conference

NO.47 What is used to determine compressed air cleanliness?

Needle pressure gauge

Psychrometer

Blotter test

Profilometer

NO.48 ISO SA 3 is directly equivalent to:

NACE No. 1/SSPC SP 5

NACE No. 2/SSPC SP 10

NACE No. 3/SSPC SP 6

None of the above

NO.49 You are the NACE Inspector on a 5000 sq. ft. job where SSPC PA 2 has been specified.
Assuming all areas are in compliance, how many gauge readings and spot measurements are required?

105 Gauge Readings resulting in 35 Spot Measurements

75 Gauge Readings resulting in 25 Spot Measurements

225 Gauge Readings resulting in 75 Spot Measurements

45 Gauge readings resulting in 15 Spot Measurements

NO.50 Osmotic blistering is most likely to occur as a result of

inadequate anchor pattern/surface profile.

overcoating a surface contaminated with chemical salts.

airless spray application

applying tine coating too thin.

NO.51 Excessive working of the surface with a power grinder can be detrimental because excessive burnishing

scratches the surface too deeply resulting in uneven coating application

develops a polished surface, which is a poor anchor profile for most coatings

damages structural elements thereby speeding up the corrosion process.

develops a good anchor profile resulting in uneven coating application.

NO.52 You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors.
Your FIRST preferred course of action is to:

Accept the assignment without hesitation

Advise the prospective employer that you cannot accept the position

Meet with the prospective employer to determine the scope of your role

Review the NACE Attestation prior to making a decision

NO.53 Which of these tests uses a syringe?

Sleeve test

Potassium ferricyanide

Bresle patch

Soluble salts meter

NO.54 Prior to using Inspection Tools the inspector must:

Ensure the instrument is within calibration parameters

Be trained on how to use the instrument

Read the manufactures’ instructions

a), b) & c)