This page was exported from Best Free Exam Guide [ http://free.exams4sures.com ] Export date:Fri Mar 14 20:26:22 2025 / +0000 GMT ___________________________________________________ Title: Verified 300-410 dumps Q&As 100% Pass in First Attempt Guaranteed Updated Dump from Exams4sures [Q45-Q64] --------------------------------------------------- Verified 300-410 dumps Q&As 100% Pass in First Attempt Guaranteed Updated Dump from Exams4sures Pass CCNP Enterprise 300-410 Exam With  740 Questions NO.45 Refer to the exhibit.An engineer is trying to add an encrypted user password that should not be visible in the router configuration.Which two configuration commands resolve the issue? (Choose two)  password encryption aes  username Admin password Cisco@maedeh motamedi  username Admin password 5 Cisco@maedeh motamedi  username Admin secret Cisco@maedeh motamedi  no service password-encryption  service password-encryption NO.46 Refer to the exhibit.An engineer applies a prefix-list filter that filters most of the network 10 prefixes instead of allowing them.Which action resolves the issue?  Modify the ip prefix-list ElGRP seq 10 permit 10.0.0.0/8 le 9 command.  Modify the command Modify the Ip prefix-list ElGRP seq 10 permit 10.0.0.0/8 le 32 command.  Modify the Ip prefix-list ElGRP seq 20 permit 0.0.0.0/0 le 32 command.  Modify the ip prefix-list ElGRP seq 20 permit 10.0.0.0/8 ge 9 command NO.47 Refer to the exhibit. The static route is not present in the routing table of an adjacent OSPF neighbor router. Which action resolves the issue?  Configure the next hop of 10.20.20.1 in the prefix list DMZ-STATIC  Configure the next-hop interface at the end of the static router for it to get redistributed  Configure a permit 20 statement to the route map to redistribute the static route  Configure the subnets keyword in the redistribution command NO.48 Refer to the exhibit. An engineer notices a connectivity problem between routers R1 and R2. The frequency of this problem is high during peak business hours. Which action resolves the issue?  Increase the MTU on the interfaces that connect R1 and R2.  Increase the available bandwidth between R1 and R2.  Decrease the EIGRP keepallve and hold down timers on R1 and R2.  Set static EIGRP neighborship between R1 and R2. NO.49 An engineer creates a Cisco DNA Center cluster with three nodes, but all the services are running on one host node. Which action resolves this issue?  Restore the link on the switch interface that is connected to a cluster link on the Cisco DNA Center  Click the master host node with all the services and select services to be moved to other hosts  Enable service distribution from the Systems 360 page.  Click system updates, and upgrade to the latest version of Cisco DNA Center. NO.50 Refer to Exhibit.The network administrator configured the branch router for IPv6 on the E0/0 interface. The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?  Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command  Disable IPv6 on the E0/0 interface using the no ipv6 enable command  Enable the IPv4 address family under the E0/0 interface by using the address-family ipv4 unicast command  Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E0/0 interface ExplanationOnce again, Cisco changed the IOS configuration commands required for OSPFv3 configuration. The new OSPFv3 configuration uses the “ospfv3” keyword instead of the earlier “ipv6 router ospf” routing process command and “ipv6 ospf” interface commands.The Open Shortest Path First version 3 (OSPFv3) address families feature enables both IPv4 and IPv6 unicast traffic to be supported. With this feature, users may have two processes per interface, but only one process per address family (AF).NO.51 Refer to the exhibit.An engineer cannot copy the IOS.bin file from the FTP server to the switch.Which action resolves the issue?  Allow file permissions to download the file from the FTP server.  Add the IOS.bin file, which does not exist on FTP server.  Make memory space on the switch flash or USB drive to download the file.  Use the copy flash:/ ftp://cisco@10.0.0.2/IOS.bin command. NO.52 Refer to Exhibit.PC2 is directly connected to R1. A user at PC2 cannot Telnet to 2001:db8:a:b::10. The user can ping2001:db8:a:b::10 and receive DHCP-related information from the DHCP server. Which action resolves the issue?  Remove sequence 10 and put it back as sequence 25.  Remove sequence 20 and put it back as sequence 45.  Remove sequence 30 and put it back as sequence 5.  Remove sequence 40 and put it back as sequence 15. NO.53 Refer to the exhibit. The network administrator configured the branch router for IPv6 on the E 0/0 interface The neighboring router is fully configured to meet requirements, but the neighbor relationship is not coming up. Which action fixes the problem on the branch router to bring the IPv6 neighbors up?  Enable the IPv4 address family under the E 0/0 interface by using the address-family Ipv4 unicast command  Disable IPv6 on the E 0/0 interface using the no ipv6 enable command  Enable the IPv4 address family under the router ospfv3 4 process by using the address-family ipv4 unicast command  Disable OSPF for IPv4 using the no ospfv3 4 area 0 ipv4 command under the E 0/0 interface. ExplanationOnce again, Cisco changed the IOS configuration commands required for OSPFv3 configuration. The new OSPFv3 configuration uses the “ospfv3” keyword instead ofthe earlier “ipv6 router ospf” routing process command and “ipv6 ospf” interface commands.The Open Shortest Path First version 3 (OSPFv3) address families feature enables both IPv4 and IPv6 unicast traffic to be supported. With this feature, users may havetwo processes per interface, but only one process per address family (AF).NO.54 Refer to the exhibit.R5 should not receive any routes originated in the EIGRP domain. Which set of configuration changes removes the EIGRP routes from the R5 routing table to fix the issue?  R4route-map O2R deny 10match tag 111route-map O2R permit 20!router ripredistribute ospf 1 route-map O2R metric 1  R2route-map E20 deny 20R4route-map O2R deny 10match tag 111!router ripredistribute ospf 1 route-map O2R metric 1  R4route-map O2R permit 10match tag 111route-map O2R deny 20!router ripredistribute ospf 1 route-map O2R metric 1  R4route-map O2R deny 10match tag 111!router ripredistribute ospf 1 route-map O2R metric 1 In this question, routes from EIGRP domain are redistributed into OSPF (with tag 111) then RIPv2 but without any filtering so R5 learns all routes from both EIGRP and OSPF domain. If we only want R5 to learn routes from OSPF domain then we must filter out routes with tag 111 and permit other routes.The line “route-map O2R permit 20” is important to allow other routes because of the implicit deny all at the end of each route-map.NO.55 Refer to the exhibits. A company with autonomous system number AS65401 has obtained IP address block 209.165.200.224/27 from ARIN. The company needed more IP addresses and was assigned block 209.165.202.128/27 from ISP2. An engineer in ISP1 reports that they are receiving ISP2 routes from AS65401.Which configuration on R1 resolves the issue?         https://www.cisco.com/c/en/us/support/docs/ip/border-gateway-protocol-bgp/23675-27.htmlNO.56 Which configuration enabled the VRF that is labeled “Inet” on FastEthernet0/0?  R1(config)# ip vrf InetR1(config-vrf)#ip vrf FastEthernet0/0  R1(config)#ip vrf Inet FastEthernet0/0  R1(config)# ip vrf InetR1(config-vrf)#interface FastEthernet0/0R1(config-if)#ip vrf forwarding Inet  R1(config)#router ospf 1 vrf InetR1(config-router)#ip vrf forwarding FastEthernet0/0 NO.57 Refer to the exhibits. An engineer filtered messages based on severity to minimize log messages.After applying the filter, the engineer noticed that it filtered required messages as well. Which action must the engineer take to resolve the issue?  Configure syslog level 2.  Configure syslog level 3.  Configure syslog level 4.  Configure syslog level 5. https://www.cisco.com/c/en/us/td/docs/routers/access/wireless/software/guide/SysMsgLogging.ht mlNO.58 A network is configured with IP connectivity, and the routing protocol between devices started having problems right after the maintenance window to implement network changes. Troubleshoot and resolve to a fully functional network to ensure that:R4R5 See the solution below in Explanation.Explanation:R4Int range et0/0 – 1Ip ospf authentication message-digestIp ospf message-digest-key 1 md5 CCNPRouter ospf 1Redistribute connected subnets route-map to-ospf metric-type 1Copy run startR5Int range et0/0 – 1Ip ospf authentication message-digestIp ospf message-digest-key 1 md5 CCNPInterface eth 0/1Ip ospf cost 10Copy run startVERIFICATION:-Graphical user interface, text, application Description automatically generatedNO.59 Refer to the exhibit.Which subnet is redistributed from EIGRP to OSPF routing protocols?  10.2.2.0/24  10.1.4.0/26  10.1.2.0/24  10.2.3.0/26 NO.60 A network engineer must configure an EIGRP stub router at a site that advertises only connected and summary routes. Which configuration performs this task?  router eigrp 100eigrp stub redistribute  router eigrp 100eigrp stub  router eigrp 100eigrp stub connected  router eigrp 100eigrp stub summary NO.61 What is the output of the following command:show ip vrf  Shows default RD values  Displays IP routing table information associated with a VRF  Shows routing protocol information associated with a VRF.  Displays the ARP table (static and dynamic entries) in the specified VRF An example of the “show ip vrf” is shown below:NO.62 Refer to the exhibit. An administrator configured a Cisco router for TACACS authentication, but the router is using the local enable password instead. Which action resolves the issue?  Configure the aaa authentication login default group admin local if-authenticated command instead.  Configure the aaa authentication login admin group tacacs+ local enable none command instead.  Configure the aaa authentication login admin group tacacs+ local if-authenticated command instead.  Configure the aaa authentication login admin group admin local enable command instead. NO.63 Refer to the exhibit.The network administrator configured VRF lite for customer A. The technician at the remote site misconfigured VRF on the router. Which configuration will resolve connectivity for both sites of customer a?  Option A  Option B  Option C  Option D NO.64 Drag and drop the addresses from the left onto the correct IPv6 filter purposes on the right.  Loading … Pass 300-410 Tests Engine pdf - All Free Dumps: https://www.exams4sures.com/Cisco/300-410-practice-exam-dumps.html --------------------------------------------------- Images: https://free.exams4sures.com/wp-content/plugins/watu/loading.gif https://free.exams4sures.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2025-01-27 16:51:22 Post date GMT: 2025-01-27 16:51:22 Post modified date: 2025-01-27 16:51:22 Post modified date GMT: 2025-01-27 16:51:22