NS0-184 Study Guide Brilliant NS0-184 Exam Dumps PDF [Q23-Q45]

NEW QUESTION 23
On which type of network interfaces are the cluster interconnect LIFs created?

NEW QUESTION 24
You installed a new 4-node AFF A400 ONTAP 9.8 cluster. The AFF400 controller data ports were automatically discovered by “automatic port placement”.
In this scenario, which two ONTAP network settings were automatically configured? (Choose two.)

NEW QUESTION 25
Click the Exhibit button.

You are installing a 2-node AFF A400 switchless cluster. You have cabled the management network to the e0M port. NetApp also recommends cabling to a redundant management network switch.
Referring to the exhibit, to which port should the redundant management network be cabled?

NEW QUESTION 26
After completing a technology refresh, you need to schedule a knowledge transfer with a customer. The customer asks you to address a number of topics during the meeting.
In this scenario, which two topics would be appropriate to address? (Choose two.)

NEW QUESTION 27
You are expanding an existing cluster that uses BES-53248 cluster interconnect switches. You connected the new controllers to ports 0/17 through 0/20. However, you are unable to join the new nodes to the cluster.
Which action must be taken to solve the problem?

NEW QUESTION 28
Before installing an 8-node cluster for a customer, you want to validate compatibility with existing hardware.
Which two tools would you use to validate the configuration? (Choose two.)

NEW QUESTION 29
After moving a new AFF A400 cluster into production, the administrator notices error events in ONTAP System Manager regarding SAS HA issues.
In this scenario, which NetApp tool would have identified these errors after the installation process?

NEW QUESTION 30
Click the Exhibit button.

You are reviewing the setup of a recently installed FAS9000 switched cluster. As shown in the exhibit, the cluster interconnects are connected to a pair of Cisco Nexus 3132Q-V 40 Gb ports.
For a high availability, which ports should swap Ethernet cables?

NEW QUESTION 31
Which command would be used to measure the throughput and latency of traffic between nodes?

NEW QUESTION 32
You use the system health subsystem show command to troubleshoot your newly installed ONTAP cluster.
In this scenario, which two health outputs would this command show you? (Choose two.)

NEW QUESTION 33
Click the Exhibit button.

A customer has two Cisco 40GbE data switches. They want to connect the switches to an AFF A400 HA pair. The switches and the AFF A400 are approximately seven meters apart.
Referring to the exhibit, which two supported actions would allow you to accomplish this task? (Choose two.)

NEW QUESTION 34
Click the Exhibit button.

Referring to the exhibit, you installed a new AFF A250 HA system with FC at a customer site. The customer asks how many ports can be used for the Ethernet host connections.
In this scenario, what would you tell the customer?

NEW QUESTION 35
After the installation of a new ONTAP 9.8 cluster, you have to verify if AutoSupport works.
In this scenario, which two commands would you use to accomplish this task? (Choose two.)

NEW QUESTION 36
You have a 4-node ONTAP 9.8 cluster with a FAS8700 HA pair that serves iSCSI LUNs. You are adding a new AFF A250 HA pair to the cluster with new iSCSI SAN LIFs. You need to allow non-optimized data paths from the AFF A250 nodes to the existing LUNs on the FAS8700 nodes.
In this scenario, which two ONTAP configuration settings must you verify? (Choose two.)

NEW QUESTION 37
You have a 2-node FAS8300 switchless ONTAP 9.8 cluster that serves NAS volumes. You have a data SVM that connects to the network using multimode LACP with VLAN tags.
In this scenario, which front-end FAS8300 network port would you create the data LIFs?

NEW QUESTION 38
Your customer plans to expand a 2-node FAS2750 switched cluster with two new controllers.
In this scenario, which two prerequisites should you examine in advance? (Choose two.)

NEW QUESTION 39
Click the Exhibit button.

Referring to the exhibit, what information is forwarded to syslog after you enter the scripted install commands? (Choose two.)

NEW QUESTION 40
You have installed and configured a new AFF C190 cluster with ONTAP 9.7. Your customer wants you to install the latest version of ONTAP.
In this scenario, what are two methods to update ONTAP? (Choose two.)

NEW QUESTION 41
You are preparing for the installation of a new 2-node cluster with ONTAP 9.7 using NL-SAS drives. Your customer wants to use the cluster exclusively with FlexGroups.
In this scenario, which two statements are correct? (Choose two.)

NEW QUESTION 42
Click the Exhibit button.

You are adding new DS224C shelves in a new stack to your cluster with FAS8060 controllers running ONTAP 9.7.
Referring to the exhibit, which two actions should be performed to the cluster before installing the new shelves? (Choose two.)

NEW QUESTION 43
You want to disconnect a DS224C shelf with 3.8 TB NetApp Storage Encryption (NSE) SSDs to an AFF A300 HA pair with two DS224C shelves with 3.8 TB SSDs without NSE in one stack.
In this scenario, how would you add the shelf?

NEW QUESTION 44
You installed two separate clusters in an isolated data center without outbound network access. The customer wants to troubleshoot issues locally and also create custom Excel reports for capacity utilization from a local server.
In this scenario, which NetApp tool would satisfy this requirement?

NEW QUESTION 45
Click the Exhibit button.

You want to add a FAS2750 HA pair to an existing 6-node cluster.
Referring to the exhibit, which action would you perform to begin adding the node?