[Feb-2024] HPE0-S59 Free Sample Questions to Practice One Year Update [Q20-Q37] : Best Free Exam Guide : http://free.exams4sures.com

NO.20 Your customer plans to deploy VMware ESXi 7 0 U2 and they are looking for a hardware platform mat wilt allow them to use up to 24 TB of physical memory.
Which HPE compute system meets this customer’s requirements?

HPE ProLiant DL380 Gen 10 Plus

HPE Synergy 480 Gen10 Plus

HPE ProLiant DL560 Gen10

HPE Superdome Flex 280

NO.21 Your customer plans to use HPE Primera to boot HPE Synergy compute nodes. They currently have two HPE Virtual Connect SE 100Gb F32 Module for Synergy modules installed in the frame. The customer wants to use FC as a storage access protocol What must be done to complete this task?

Enable FC primary and secondary boot on the modules through the HPE OneView interface

FC connectivity on the modules should be enabled through the service console by disabling FCoE.

Add FC upgrade licenses in HPE OneView that will enable FC connectivity for the modules

Enter both modules into a maintenance mode, then enable FC connectivity through CLI

NO.22 Your customer wants to compare HPE Superdome Flex with HPE Superdome Flex 280.
Which statement about these two systems is true?

Only HPE Superdome Rex 280 can be managed using HPE OneView

Only HPE Superdome Flex supports HPE Persistent Memory

Only HPE Superdome Flex 280 can support multiple nPars

Only HPE Superdome Flex supports 32 sockets and 48TB of memory

NO.23 Your customer has the following HPE Synergy setup
– 3 HPE Synergy 12000 Frames
– 4 HPE Virtual Connect SE 100 Gb F32 Modules
– 2 HPE Synergy 50 GO Interconnect Link Modules
– 36 HPE Synergy 480 Gen10 Plus compute modules
– 2 HPE Composer 2 modules
Which statement about this setup is true?

To use all compute nodes, the customer must create at least two logical enclosures

To manage all frames, the customer must buy two additional HPE Composer 2 modules

The customer must buy 36 HPE OneView Advanced licenses to manage compute modules

The customer can add one D3940 storage Module to each of the frames

NO.24 Your customer has 6 logical enclosures spanning 18 HPE Synergy frames. The customer needs to add one more logical enclosure based on 5 HPE Synergy frames How will this change impact the customer environment?

The customer can add a new logical enclosure to the existing setup because the maximum number of logical enclosures in a single management ring is not reached.

The customer has to expand the management ring capacity either by adding HPE Composer 2 modules or adding memory to reach 128GB per module.

The customer has to create a new management ring for new logical enclosure because the maximum number of frames m a single management ring is reached.

The customer can add a new logical enclosure to an existing setup once all required licenses are added lo HPE OneView and associated with the new frames.

NO.25 Which statement about login redistribution is true?

NO.26 Your customer has me following HPE Synergy setup
– Three frames fully populated with HPE Synergy 480 Gen10 Plus modules and 25Gb/s downlink speed formulating a single logical enclosure
– Two HPE Virtual Connect SE 100Gb F32 Module for Synergy
– Four HPE Synergy 50Gb interconnect Link Module
– Six HPE Synergy Virtual Connect SE 32Gb FC Modules
The customer needs to add a frame.
Which statement about the expansion of this setup is true?

The additional frame must have HPE Virtual Connect FC modules installed

The customer can grow the existing logical enclosure up to 5 frames

The customer has to create a new logical enclosure for the additional frame

The additional frame cannot have 12Gb SAS connection modules installed

NO.27 Your customer has an HPE Synergy platform deployed and managed using HPE OneView. The customer also has HPE Superdome Flex with RMC deployed They plan to deploy a second nPar and HPE Superdome Flex
280 They plan to manage new components using HPE OneView
What must be done to achieve this goal?

The customer must use IL05 to add HPE Superdome Flex systems to HPE OneView

The customer should deploy an HPE OneView appliance for HPE Superdome Flex management

The customer must add a second Rack Management Controller for HPE Superdome Flex 280

The customer has to add HPE Superdome Flex to the HPE OneView used to manage HPE Synergy

NO.28 Which tool can be used to evaluate me health of an HPE Oneview appliance before proceeding with an appliance updated.

HPE Composer Maintenance Console

HPE OneView Update Readiness Checker

HPE OneView Global Dashboard

HPE OneView Firmware Compliance Report

NO.29 Refer to the exhibit.

Which statement about this logical JBOD is true?

This logical JBOD can be connected to multiple systems to formulate a snared datastore.

After deleting this logical JBOD drives will he blocked for 12h m case this JBOD must be re-created

After deleting this logical JBOD, its drives w not be available until a clean-up procedure 6 done

This logical JBOD can be presented to the compute nodes in a different frame.

NO.30 Your customer plans to setup an HPE Synergy solution based on SY480 Gen10 compute nodes with the following connectivity options – SAS connectivity installed in the first fabric – FC connectivity Installed In the second fabric – Ethernet connectivity installed in the third fabric.
Which statement regarding this setup is true?

Each compute node must have at least 768GB of memory installed

Interconnect modules that provide SAS connectivity should be moved to the third fabric

Each interconnect module in each fabric must be properly licensed in HPE OneView

Compute nodes must have a second CPU installed to access the second fabric.

NO.31 Which statement about the SY480 Gen10 Plus Compute Module is true?

It cannot be mixed with Gen9 compute modules in the same frame.

It supports 8 memory channels and memory DIMMs of up to 256GB.

It only supports NVDIMM Persistent Memory.

It supports “3rd Gen AMO EPYC Server Processors with 64 cores.

NO.32 An administrator tries to open iLO interlace from HPE OneView Instead of being automatically logged in a login prompt displays Where should you start the troubleshooting process?

At the iLO interface to verify whether the ILO Advanced license is properly applied

At HPE OneView Interface to verify whether the server is In the maintenance mode

At the iLO interface to verify whether the SSO certificate is removed from an iLO.

At HPE OneView Interface to verify whether the iLO processor is disabled

NO.33 Refer to the exhibit.

Which statement about this logical interconnect group is true?

The master modules are located in the interconnect bays 2 and 5

For the given downlink speed, the maximum number of frames is reached

Both master modules are located in the same HPE S ynergy frame

To use interconnect bay set 3, all compute nodes must be half-height

NO.34 You need to configure a RoCE network to enable lossless networking for HPE J2000 Flash Enclosure support Which interconnects are required to support this connection? (Select two.)

HPE Virtual Connect SE 40Gb F8 Module for HPE Synergy

HPE Virtual Connect SE 16Gb FC Module for HPE Synergy

HPE Virtual Connect SE 100Gb F32 Module for HPE Synergy

HPE Virtual Connect SE 32Gb FC Module for HPE Synergy

Brocade 16Gb Fibfe Channel SAN Switch Module for HPE Synergy

Brocade 32Gb Fibre Channel SAN Switch Module for HPE Synergy

NO.35 Your customer experienced some problems caused by outdated HPE Superdome Flex firmware. Which update method should they use to avoid these issues in the future?

HPE OneView method for I/O firmware update procedure

RMC CLI to update I/O and HPE Persistent Memory firmware

HPE OneView IT HPE Persistent Memory firmware must be updated.

HPE SUM if HPE Persistent Memory firmware must be updated

NO.36 Your customer has an HPE Synergy frame equipped with a D3940 Storage Module. Each of the compute nodes has an appropriate storage controller Installed and two 12Gb SAS switches installed in the first fabric.
The customer reports that compute nodes cannot access the storage module. What should you verify first when troubleshooting this problem?

If the D3940 module is imported in managed state that allows volume provisioning.

If there Is a logical interconnect created based on the 12Gb SAS switches.

If the D3940 storage module is property licensed through HPE OneView interface.

If there is at least one ISCSI network configured that will provide access to the module.

NO.37 Which statement about a new HPE SimpliVity deployment is true?

New HPE SimpliVity deployments give customer flexible choice of hypervisor

All new HPE SimpliVity models are based on AMD CPUs

All new HPE SimpliVity models support deduplication and compression

New HPE SimpliVity deployments are licensed per node not per physical socket