HPE6-A72 Exam Dumps Pass with Updated 2023 Certified Exam Questions [Q22-Q41] : Best Free Exam Guide : http://free.exams4sures.com

Q22. Interface 1/1/1 is up
Admin state is up
Link transitions: 1
Description: TO_PC-1
Hardware: Ethernet, MAC Address: 00:11:22:33:44:55
MTU 1500
Type 1GbT
Full-duplex
qos trust none
Speed 1000 Mb/s
Auto-negotiation is on
Flow-control: off
Error-control: off
MDI mode: MDIX
VLAN Mode: access
Access VLAN: 1111
Which command will produce the above output?

show interface vlan 1111

show interface 1/1/1

show interface gigabit 1/1/1

show vlan 1111

Q23. Refer to the exhibit.

The above command was applied to an Aruba AOS-CX 6300M 24-port switch with 4-port SFP56 uplinks. All ports are set as access switchports.
Which ports carry VLAN 1 traffic?

1/1/8, 1/1/10, 1/1/5-1/1/24

1/1/1-1/1/28

1/1/1-1/1/24

1/1/8-1/1/10, 1/1/5-1/1/28

Q24. The following command is issued:
Switch# checkpoint rollback start
What is the result?

The command will fail because rollback commands must be issued from global-config mode.

The switch will revert the running-configuration to the checkpoint called ‘start1 without a reboot.

The command will fail because it is incomplete.

The switch will use the checkpoint ‘rollback1 as the starting configuration on next reboot.

Q25. Refer to the exhibit.

The above output is the result of issuing the command show system resource-utilization.
What command should be used to enable terminal output line by line or page by page?

The command page

The command terminal length 30

The command more

The command less

Q26. Which port or ports should be allowed through a firewall so that an AOS-CX switch can act as an SNMP Agent?

UDP 1812 and UDP 1813

UDP 161

TCP 443

UDP 162

Q27. The section in blue can be ignored.
SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?

Q28. Which two statements accurately describe stacking with Aruba switches? (Choose two.)

A VSF stack is allowed between an AOS-CX 6300M and 6300F switches.

VSF is a core or aggregation layer stacking technology due to the high resiliency of sharing a single control plane.

The VSF feature is not compatible between AOS-CX and AOS platforms.

A VSF stack is allowed between an AOS 5400R and an AOS-CX 6400.

VSF and VSX are stacking option with the AOS-CX 8320. 8325. 8400. and 6400 models.

Q29. Review the exhibit.
As the frame traverses from **PC-1** to **Server-1**, the VLAN tag will be removed.
Click on the interface (circled in green) where the VLAN tag will be removed.

Q30. Refer to the exhibit.

Traffic is failing between Core-1 and Host-B. IP addressing has correctly been applied, and all interfaces are attached to the vrf GREEN.
Which configuration will correct the issue?

Core-2(config)# ip route 0.0.0.0/0 10.1.1.1 vrf GREEN
Host-B: assign the default-gateway address 10.1.20.181

Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN
Host-B: assign the default-gateway address 10.1.20.181

Core-1(config)# ip route 10.1.20.0/24 10.1.1.2 vrf GREEN
Host-B: assign the default-gateway address 10.1.20.1

Host-B: assign the default-gateway address 10.1.20.181

Q31. Refer to the exhibit.

What command will display the debug l2mac events?

show module L2MAC

show debug terminal

show debug buffer module L2MAC

show debug all

Q32. With what other technology does Half Duplex communication closely match?

a pair of fiber optic strands allowing transmit on one and receive on the other at the same time

a mobile phone call

point-to-point connections between two switches allowing concurrent transmit and receive

CB radio using push-to-talk

Q33. What command will save your configuration on an Aruba AOS-CX switch so that your changes automatically load on next reboot?

copy running-config checkpoint startup-config

copy startup-config running-config

copy running-config initial-checkpoint

copy running-config default

Q34. Refer to the exhibit.

The Aruba 8400 in the exhibit is member 2 of a VSX stack.
Which command will enter the interface sub configuration mode for the port, indicated by the orange square?

8400(config)# interface 2/4/15

8400(config)# interface 1/7/16

8400(config)# interface 1/4/15

8400(config)# interface 2/3/17

Q35. Which field in the IPv4 header indicates whether the IP packet carries TCP or UDP traffic?

Protocol

IHL

TTL

Identification

Q36. Refer to the exhibit.

Using the static IP address configured above, what is the converted binary value of the third octet assigned to the local interface?

11010101

10110001

01001011

11111000

Q37. What is a benefit of choosing a 3-Tier design with routing at the Aggregation layer?

Better Core router performance by offloading processing

Shifting endpoint access to the Aggregation layer from the Access layer

Using access control lists (ACLs) at the Core to improve performance

Connecting WAN/MPLS and Data center access to the Aggregation layer

Q38. Which command can be used to find the serial number of an Aruba OS-CX switch?

The command inventory

The command version

The command show running-configuration

The command show system

Q39. Refer to the exhibit.

All four switches in the diagram have been configured with the region name “Aruba1”.
What two other MSTP configurations must match for switches within the same MST region? (Choose two.)

MST region type

MST Bridge ID

MST version number

MST revision number

MST VLAN to instance mapping

Q40. Which statement is correct regarding powering an Aruba Access Point?

PoE or PoE+ is only used with Ethernet that is carried over multi-mode fiber cabling.

Using switchports for this reason is unnecessary, because Aruba Access Points typically use an AC to DC power adapter to draw power.

PoE or PoE+ enabled switchports are rarely used given concerns about causing electrical interference, with the data also carried over Ethernet cabling.

Most administrators use PoE or PoE+ enabled switchports to provide both Ethernet connectivity and power to the AP.

Q41. SW1(config)# interface 1/1/1-1/1/2
SW1(config-if-<1/1/1-1/1/2)# vlan access 2
SW1(config-if-<1/1/1-1/1/2)# exit
SW1(config)# interface 1/1/11-1/1/17
SW1(config-if-<1/1/11-1/1/17)# vlan access 17
SW1(config-if-<1/1/11-1/1/17)# exit
After completing the above commands, what is the expected output of show vlan with no other vlan commanded having been added?

Option A

Option B

Option C

Option D