[Aug-2022] HPE6-A75 Exam Dumps - Free Demo & 365 Day Updates [Q11-Q34] : Best Free Exam Guide : http://free.exams4sures.com

NEW QUESTION 11
What is a primary use case for RPVST+ on AOS-Switches?

more granular load balancing than MSTP when access switches connect to two core switches

enhanced loop protection in an MSTP network

integration of AOS-Switches in a heterogeneous vendor network that uses the Cisco protocol

seamless integration with RSTP

NEW QUESTION 12
Refer to the exhibit.

A company has attempted to implement OSPF without success. The devices in Area I need to be able to reach Area 2. Routes should be aggregated for advertisement in other areas. What must be changed to meet these requirements?

Change Area 3 to Area 0; remove Area 1 from Switch-2 and Area 2 from Switch-1.

Add the 10.2.0.0/16 range on Swttch-1 and the 10.1.0.0/16 range on Switch-2.

Add Area 1 and Area 2 on VIAN 100 on both Switch-1 and Switch-2. Remove Area 3.

Move the 10.1.0.0/16 range to Area 2 on Switch-1 and the 10.2.0.0/16rangetoArea 1 onSwitch-2.

NEW QUESTION 13
Refer to the exhibit.

A network administrator sets up 802.1X authentication to a RADIUS server on an AOS-Switch. The RADIUS server and user devices are both set up to use REAP MSCHAPv2. The administrator tests the authentication and sees the output shown in the exhibit. Which issue could cause this output?

The RADIUS shared secret does not match on the switch and the server.

The administrator entered the wrong password for the test account.

The switch does not have a certificate tor port-access installed on the switch.

The switch port is set for user mode 801. IX. but the RADIUS server is set for port mode.

NEW QUESTION 14
Refer to the exhibit.

Based on the Enforcement Policy configuration, when a user with Role Engineer connects to the network and the posture token assigned is Unknown, which Enforcement Profile will be applied?

EMPLOYEE_VLAN

RestrictedACL

Deny Access Profile

HR VLAN

Remote Employee ACL

NEW QUESTION 15
Refer to the exhibit.

Controllers are configured m a cluster as shown in the exhibit. These are the network details.
* A Mobility Master (MM) manages the cluster.
* The cluster contains two controllers: C l and C2.
* API and AP2 use CI as their Active AP Anchor Controller (A-AAC). with C2 as their Standby AAC (S-AAC).
* AP3 and AP4 use C2 as their A-AAC, with CI as their S-AAC.
User1 establishes a wireless connection via API, where the Active User Anchor Controller (A-UAC) assigned is CI. with C2 as the standby. What happens when User I roams the wireless network and eventually their session is handled by AP3?

The AP3’s A-AAC switches to C1, and the user’s A-UAC remains on C1.

The AP3’s A-AAC switches to C2, and the user’s A-UAC remains on C2.

The AP3’s A-AAC switches to C1, and the user’s A-UAC remains on C2.

The AP3’s A-AAC switches to C2, and the user’s A-UAC remains on C1.

NEW QUESTION 16
Refer to the exhibit.

Based on the Policy configuration shown, which VLAN will be assigned when a user with ClearPass role Engineer authenticates to the network successfully on Saturday using connection protocol WEBAUTH?

Deny Access

Employee VLAN

Internet VLAN

Full Access VLAN

NEW QUESTION 17
Which statement is true about the Endpoint Profiler? (Select two.)

The Endpoint Profiler uses DHCP fingerprinting for device categorization.

Data obtained from the Endpoint Profiler can be used in Enforcement Policy.

Endpoint Profiler requires a profiling license.

The Endpoint Profiler requires the Onboard license to be enabled.

The Endpoint Profiler can only categorize laptops and desktops.

NEW QUESTION 18
An administrator creates service-based policies for AirGroup on the Mobility Master (MM). The administrator can define location-based policy limits based on which information?

AP names, AP groups, controller names, and controller groups

AP Fully Qualified Location Names (FQLNs) and controller Fully Qualified Domain Names (FQDNs)

AP names, AP groups, and AP Fully Qualified Location Names (FQLNs)

Controller names, controller groups, and controller Fully Qualified Domain Names (FQDNs)

NEW QUESTION 19
A network administrator can set the OSPF metric-type on an AOS-Switch to Type 1 or Type 2. What is the difference?

A Type 2 metric marks external routes that can be advertised in NSSAs, while a Type 1 metric marks external routes that can only be advertised in normal areas.

A Type 2 metric assigns cost 1 to a 100 Gbps link, while a Type 1 metric assigns cost 1 to all links of 100 Mbps or higher.

A Type 2 metric is assigned to multiple external routes that are aggregated together, while a Type 1 metric does not permit external route aggregation.

A Type 2 metric stays the same as the external route is advertised, while a Type 1 metric increments with internal OSPF link costs.

NEW QUESTION 20
Refer to the exhibits.

The network administrator enters the commands shown in Exhibit 2. What is the spanning tree status on Al and A2?

A1 towards traffic, and A2 blocks traffic.

Both Al and A2 block traffic.

A1 blocks traffic, and A2 forwards traffic.

Both A1 and A2 forward traffic

NEW QUESTION 21
Refer to the exhibit.

An AD user’s department attribute is configured as *HR”. The user connects on Monday using their Windows Laptop to a switch that belongs to the Device Group HQ. Which role is assigned to the user in ClearPass?

Executive

iOS Device

Vendor

Remote Employee

HR Local

NEW QUESTION 22
Which statement is true about the databases in ClearPass?

Entries in the guest user database do not expire.

A Static host list can only contain a list of IP addresses.

Entries in the guest user database can be deleted.

Entries in the local user database cannot be modified.

The endpoints database can only be populated by manually adding MAC addresses to the table.

NEW QUESTION 23
Refer to the exhibit.

The network administrator needs to set up BGP between the two company switches. Switch-1 and Switch-2. The BGP connection does not establish. Based on the exhibits, what does the administrator need to do to fix the issue?

Enable the multihop option for the neighbor on each of the switches.

Enter the network command for 10.0.0.0/24 in the router BGP mode on each switch.

Enable BGP on the interfaces that the switches use to reach each other.

Set the update source for the neighbor to the local loopback interface on each switch.

NEW QUESTION 24
Refer to the exhibit.

mike

We can’t know this from the screenshot above.

Employee

john

NEW QUESTION 25
A company has AOS-Switches deployed at sites with inexperienced IT staff. The main office network administrators want to track if configurations change on branch switches. What should be set up for this purpose?

an SNMP trap

an RMON alarm

an auto-config server

an lP SLA profile

NEW QUESTION 26
Which is a valid policy simulation types in ClearPass? (Select three.)

Enforcement Policy

Posture token derivation

Role Mapping

Endpoint Profiler

Chained simulation

NEW QUESTION 27
An administrator deploys Aruba Mobility Controller 7005s to a company’s branch offices. The administrator wants to disable the console port to prevent unauthorized access to the controllers.
Which controller command should the administrator use to implement this policy?

no console enable

no mgmt-user console

mgmt-user console-block

console disable

NEW QUESTION 28
Refer to the exhibit.

Switch-1 and Switch-2 connect on interface A23. The switches experience a connectivity issue. The network administrator sees that both switches show this interface as up. The administrator sees the output shown in the exhibit on Switch-1.
What is a typical issue that could cause this output?

a hardware issue, such as a broken cable

asymmetric routing introduced by a routing configuration error

an issue with queuing, caused by mismatched QoS settings

mismatched IP addresses on the VLAN for the link

NEW QUESTION 29
Refer to the exhibit.

An employee connects a corporate laptop to the network and authenticates for the first time using EAP-TLS. Based on the Enforcement Policy configuration shown, which Enforcement Profile wilt be sent?

Deny Access Profile

Onboard Post-Provisioning – Aruba

Onboard Device Repository

Onboard Pre-Provisioning – Aruba

NEW QUESTION 30
An administrator wants to implement bandwidth limits for guest users to restrict their Internet usage. On the Mobility Master (MM), where would the administrator define these limits?

User role

Firewall policy

AAA policy

802.1X policy

NEW QUESTION 31
What is true about clustering and AP connections to cluster members?

The AP will always stay connected to the LMS IP address configured in the AP profile.

During rebalancing, the active load is redistributed first.

The default thresholds are 75% for the Rebalanced Threshold and 25% for the Unbalanced Threshold.

AP load balancing is disabled by default.

NEW QUESTION 32
An administrator wants to use Airwave to manually add devices on the network. Where should the administrator perform this action?

in Device Setup

in Groups

in AMP Setup

in Devices

NEW QUESTION 33
An administrator implements a standalone controller that runs ArubaOS 8.x. Which feature should the administrator configure to optimize the RF operation for the company’s WLAN?

AirMatch

Clustering

ARM

Zones

NEW QUESTION 34
An administrator mistakenly configures the wrong VLAN setting on a managed controller’s interface. This causes the controller to lose management access to the Mobility Master (MM).
Which mechanism will then attempt to restore the previous working configuration on the managed controller?

disaster recovery

auto-rollback

restore config

bulk configuration

[Aug-2022] HPE6-A75 Exam Dumps - Free Demo & 365 Day Updates [Q11-Q34]

HP HPE6-A75 Exam Syllabus Topics: