Free EMC DES-DD33 Study Guides Exam Questions & Answer [Q28-Q45] : Best Free Exam Guide : http://free.exams4sures.com

NO.28 What happens to the data when it is moved from the active tier to cloud tier?

It is deduplicated and stored in a file system in the native format

It is compressed and stored as object storage in a new format

It is compressed and stored in block storage in a new format

It is deduplicated and stored in object storage in the native format

NO.29 Which component of PowerProtect DD is Data Invulnerability Architecture a feature of?

DDOS

CIFS

VTL

DD Boost

NO.30 What is a main advantage of using DD Boost instead of CIFS or NFS for a backup?

No requirement for an IP network to back up data

DD Boost does not require administration credentials

DD Boost uses integrated network acceleration

Deduplication is distributed between the backup server and client

NO.31 Which NDMP device is supported on a PowerProtect DD appliance?

NFS

DD Boost

CIFS

VTL

NO.32 What is a requirement to use the PowerProtect DD HA feature?

A single set of shared storage

Dual set of shared storage configuration

Head units and notes require an active/active configuration

Each head unit requires its own FS25 shelf

NO.33 A PowerProtect DD system is configured for VTL. The backup application requires a minimum tape capacity of 800 GiB.
What is the minimum tape type to support this requirement?

LTO-3

LTO-2

LTO-5

LTO-4

NO.34 Which PowerProtect DD procedure uses the DoD/NIST standards to provide data security?

Data Sanitization

Encryption

End-to-End Verification

Replication Encryption

NO.35 How can remote logging with a syslog server be configured on a PowerProtect DD system?

Use the CLI command log host enable

Use the DDSM to enable the remote logging

Remote logging is enabled by default

Use the DDMC to enable the remote logging

NO.36 An administrator monitors the performance statistics of a PowerProtect DD appliance. Low disk-write rates are shown, and the network inbound traffic is high.
What is the most likely cause of this behavior?

Expired segments

Known segments

Disk failure

NVRAM failure

NO.37 What are all the protocols that can be used to send data to a PowerProtect DD over Ethernet?

NDMP, NFS, VTL, and CIFS

DD Boost, VTL, CIFS, and NFS

CIFS, NFS, DD Boost, and NDMP

VTL, NFS, and NDMP

NO.38 What is the correct sequence of operations used by the PowerProtect DD DIA in the end-to-end verification process?

NO.39 A PowerProtect DD appliance has been installed at a company’s location for several months and has reached a steady state.
As a best practice, at what percentage of disk utilization should action be taken?

60%

70%

80%

95%

NO.40 A backup administrator is tasked with monitoring PowerProtect DD capacity metrics. The administrator is backing up 2 TB of data daily with a reduction rate at 5x. After data reduction, subsequent full backups compress down to 100 GB.
The initial backup requires 400 GB with a 10 percent increase in the data each day. Each incremental backup is 200 GB. After data reduction, each incremental backup is 20 GB.
What is the weekly burn rate (GB) after six daily incremental backups and one weekly backup?

200

220

400

440

NO.41 An administrator wants to integrate a PowerProtect DD appliance into their current backup environment using CIFS, NFS, DD Boost, and VTL.
Which backup applications support these protocols?

Commvault Simpana and Veritas Backup Exec

Veritas NetBackup and Dell EMC NetWorker

Dell EMC Avamar and Dell EMC NetWorker

IBM Spectrum Protect and Veritas NetBackup

NO.42 What are some possible network bottlenecks for a PowerProtect DD?

Configuration, wire speeds, switches and routers

Connectivity, firewalls, and routing protocols

Connectivity, routing protocols, and configuration

Routing protocols, switches and routers, and wire speeds

NO.43 A storage administrator finished the zoning between the PowerProtect DD and the NetWorker backup server.
How can they verify that the zoning was completed properly and the server HBA are visible?

scsitarget initiator show list

scsitarget initiator list

scsitarget show initiator

scsitarget show initiator list

NO.44 What system role is required to create the second security officer for a PowerProtect DD?

limited-admin

security officer

sysadmin

admin

NO.45 Which protocol is used with Dell EMC Cloud Tier to transfer data between a PowerProtect DD appliance and the cloud?

FTP

SFTP

HTTPS

NFS