This page was exported from Best Free Exam Guide [ http://free.exams4sures.com ] Export date:Sun Mar 16 8:09:37 2025 / +0000 GMT ___________________________________________________ Title: [May-2022] The Best HCIP Transmission H31-341 Professional Exam Questions [Q71-Q89] --------------------------------------------------- [May-2022] The Best HCIP Transmission H31-341 Professional Exam Questions Try 100% Updated H31-341 Exam Questions [2022] NEW QUESTION 71Which of the following subracks does not support the configuration of packet board?  OSN 1800II  OSN 9800 P18  OSN 8800 T16  OSN 1800V NEW QUESTION 72After the signal of the standard Ethernet frame length of 64 Bytes is connected to the Ethernet board, if the QinQ function is enabled, what is the actual frame length of the signal inside the board?  64 Bytes  84 Bytes  68 Bytes  80 Bytes NEW QUESTION 73The ways of synchronize alarms are (). (Multiple Choice)  Timing synchronization  Automatic synchronization  Manual synchronization NEW QUESTION 74What does the component of the ASON network not include?  SC  Intelligent network element  TE link  ASON domain NEW QUESTION 75During the configuration of the E-LAN, the “MAC Address Learning Mode” can be set to SVL and IVL. SVL is a stand-alone VLAN learning, and IVL is a shared VLAN learning.  TRUE  FALSE NEW QUESTION 76What are the classification of Ethernet performance tests? (Multiple choice)  Network equipment performance verification test  Network performance test  Custom test NEW QUESTION 77The following protection methods belonging to NG WDM optical layer protection are: (Multiple Choice)  Customer side 1+1 protection  Optical line protection  ODUk SNCP protection  1+1 protection inside the board NEW QUESTION 78Which of the following trails can be configured on the NMS.  client  OTS  ODUk  OCh NEW QUESTION 79In the sub-(wave) characterization test, what kind of standard does the isolation test require?  <20dB  <25dB  >20dB  >25dB NEW QUESTION 80Before creating an optical cross-connection, you need to manually configure the corresponding port of the corresponding board as a boundary port, for example, the line-side port of the FIU board between two sites.  TRUE  FALSE NEW QUESTION 81In the scenario where the non-convergence OTU processes OTN standard signals, both A and B are WDM sites. After receiving the OTUk_TIM alarm on the client side, the OTU board at station A sends the OTUk_BDI alarm to the upstream. When the TIM follow-up action is disabled, the alarm is no longer transmitted to the downstream. When the TIM follow-up action is enabled, an SF event is generated. The WDM side of the OTU board at station B reports the ODUk_PM_AIS alarm, and the ODUk_PM_AIS alarm is transmitted downstream. The client equipment reports this alarm. After the WDM side of the OTU board at station B receives the OTUk_TIM alarm and the TIM follow-up action is disabled, the alarm is no longer transmitted to the downstream. When the TIM follow-up action is enabled, an SF event is generated. After the client side of station B processes the SF event, the client equipment reports the ODUk_PM_AIS alarm.  False  True NEW QUESTION 82What are the wavelengths of the OSC channel used by the ST2 board?  1491nm  1510nm  1471nm  1511nm NEW QUESTION 83When configuring the Ethernet Layer 2 attribute, set the Default VLAN ID and VLAN Priority of the untagged frame when the TAG ID is set to Accese or Hybrid. The “VLAN priority” is set according to the QoS of the unified plan.  TRUE  FALSE NEW QUESTION 84In the WDM system, after a certain distance of transmission, the optical signal-to-noise ratio of the receiving signal will be reduced to a certain extent. What is the main reason?  Fiber attenuation is too large  Use of the splitter combiner  Use of EDFA  No new fiber is used NEW QUESTION 85Which of the following statements about the line fiber quality monitoring performance parameters is wrong?  The pulse width of emitted optical pulses varies according to monitoring modes, and affects the detection distance and measurement precision. A greater pulse width provides a larger dynamic range, longer detection distance and better measurement precision.  When the pulse width increases, the light emitting time increases and consequently a larger energy is obtained. This means that a larger dynamic range can be acquired but also larger dead zones will result.  The total fiber loss will affect the detection distance and the dynamic range is fixed for the same detection mode. Therefore, a larger total fiber loss indicates a smaller detection distance.  Measurement is performed multiple times within the detection time. The average value is obtained based on the measurement results to improve the measurement precision. The actual duration from the time when a detection event starts to the time when the detection results are returned will be longer than the Detection time. NEW QUESTION 86Which of the following monitoring boards do not support the processing and transparent transmission of 1588V2 signals? (Multiple choice)  ST2  SC2  SC1  AST2 NEW QUESTION 87Which of the following description is wrong about the content of the formula for calculating the maximum line rate (N=Ratc/((L+7+1+M)x8))?  L is in standard Ethernet frame length with a minimum value of 64Bytes  M is the frame gap, and the minimum IFG (minimum frame gap) is 8 bytes.  Rate indicates the line rate of the physical layer. If the device port is FE, then Rate=100Mbit/s.  “8” outside the brackets is 1 Byte containing 8 Bits NEW QUESTION 88Which of the following scenarios does the meter test apply to? (Multiple choice)  Exclude external issues with the transport device  Equipment docking problem  Locate the faulty board  Equipment performance indicator problem NEW QUESTION 89What should I pay attention to when commissioning a 100G and 10G hybrid transmission system? (Multiple Choice)  Pay attention to the mixed spectrum. The spectrum of the 100G signal is wider and looks lower than the 100G signal in the spectrum, but the actual optical power is equivalent.  For a hybrid transmission system with dispersion compensation, the dispersion compensation requirements are consistent with the requirements in a 10G non-coherent system.  In order to accurately measure the optical power of 100G wavelength, it must be debugged using a spectrum analyzer or a MAC card.  The optical power of the 100G signal is recommended to be higher than the optical power of the 10G signal, but not higher than the single-wave nominal value of the optical panel.  Loading … H31-341 Exam Questions Get Updated [2022] with Correct Answers: https://www.exams4sures.com/Huawei/H31-341-practice-exam-dumps.html --------------------------------------------------- Images: https://free.exams4sures.com/wp-content/plugins/watu/loading.gif https://free.exams4sures.com/wp-content/plugins/watu/loading.gif --------------------------------------------------- --------------------------------------------------- Post date: 2022-05-12 23:21:08 Post date GMT: 2022-05-12 23:21:08 Post modified date: 2022-05-12 23:21:08 Post modified date GMT: 2022-05-12 23:21:08